1. The rules and/or regulations set forth herein do not express or imply warranty of safety from publication of or compliance with these rules and/or regulations. They are intended as a guide for the conduct of the sport, and are in no way a guarantee against injury.

2. Track rules shall apply at all track sanctioned events.

3. Track officials shall have full authority over track sanctioned events. Track officials may disqualify any competitor for rules violation, hazardous action, or assaults or threats against any official.

4. All Track race cars subject to be inspected by Track. inspectors at any time.

5. All cars must be stock appearing, with full bodies and full frames, from bumper to the center of the rearend. Fabricated tube frames can be used from the center of the rear axle back. Must use 2X3" Square Tubing..

6. Minimum weight, steel or aluminum, completely stock body 3,000 lbs. with driver at all times. Maximum weight 3,700 lbs. with driver at all times.

7. Minimum wheel base 108".

8. 4" maximum rake from front firewall to rear of car.

9. 8" maximum spoiler height. No outside iron or rub rials.

10. Cars must have solid front and rear firewalls. No holes in firewall. Steel floorboards required on drivers side. No aluminum.

11. Full six point cage is mandatory. Front and rear hoop is recommended. Roll cage must be securely mounted to the frame. Roll cages will be inspected. Roll bars in drivers compartment must be padded with proper padding.

12. All cars must have fuel cells, 32 gal. max. No boat tanks. Fuel cell must be securely mounted inside trunk area. Tank should be mounted as far forward as possible and protected by at least one bar or hoop. The firewall must be between driver and fuel cell. Track prefers use of smaller fuel cell.  

13. Driver's seat must be securely mounted to frame and/or roll cage. 

14. No plating of entire frame. Broken sections may be repaired with plate or patch.

15. A minimum of 3 (three) 3/8" diameter bars in front of driver. Bars must be welded in.

16. All chrome and moldings must be removed. Bumper may be reinforced with 1(one) 2 1/2" O.D. Max. pipe. A single loop around the front to protect the radiator is allowed, but cannot exceed 1 3/4" O.D. and must be hidden inside the car. Upright support to front of radiator cannot exceed 3" in front of radiator. A chain or small bar for tow truck pick up is required front and rear. 

17. Battery must be securely mounted outside the driver's compartment.

18. Drive shaft must be painted white or silver. Drive shaft loop is required. Loop must not be more than 6" to front of drive shaft.

19. Brakes on all 4 (four) wheels must work at all times. Racing or at inspection.

20. Four Weight Jacks and Racing Shocks allowed. One shock per wheel.

21. Oversize Lugs 9/16" - 5/8" studs are required.

22. Wheels maximum 8" width steel. No aluminum wheels. Oversize lug nuts are required. Steel 8" racing wheels are allowed. One bead lock on right rear only.

23. No cutting of sheet metal for easy entry. A minimum of 3(three) door bars are required on the drivers side. Bars must be of same tubing and diameter of roll cage. Doors must be welded shut.

24. All cars must have bumpers securely welded or bolted and should be stock appearing. A bar or pipe must extend to end of bumper through quarter panel to frame to prevent bumpers from getting hooked. No sharp edges on bumpers.

25. Front Tubular Upper Control Arms allowed

26. Rear Suspension must be stock 4 link with upper and lower control arms. Uppers may be modified on top for pinion angle.

27. 1(one) radiator only in stock location. No cutting of hood for radiator clearance.

28. Stock factory type transmission only. Single disk factory type clutch only. No high dollar clutches or aluminum flywheels. 180 degree 1/2" thick scatter shield (blow proof) mandatory. Automatic transmissions must run a torque converter. No trick transmissions. All transmissions must have a working torque converter.

29. Any stock rear end, Locked or Posi-Traction, Floater Rear Ends Allowed(No Aluminum components).

30. Gasoline only. No alcohol. No nitro or nitrous oxide.

31. Tires: Hoosier 26.5x7 or E-Mods 8in. Only Hard Tires (A). No grinding of tires.

32. Any automotive engine originally manufactured by an American manufacturer for passenger car use. Cast Iron blocks only. Steel heads only. Aluminum intakes OK. Headers with collectors OK. No roller cams.

33. 4412 Holley Carburator-Choke Horn may be cut off. Carburator not to exceed 500 C.F.M. No electric fuel pumps. Risers may not exceed 2" including gaskets. No alterations to booster, or alterations to allow additional air to be picked up below the opening of the venturis.

34. #1 Spark plug on engines must be even or in front of upper ball joint.

35. Engine Claim-NONE

36. Full Face Snell Approved SA-95 helmets or newer helmets are manditory. Motorcycle helmets -95 or newer allowed with Nomex Head Sock.

37. Numbers must be 17" high and 3" wide minimum on each door and roof.  

38. Approved racing helmet with shield required. Fire suit required. Fireproof gloves recommended.

39. Five point harness 2" crotch strap, 3" should and 3" lap belts required.

40. No radios. No mirrors.

41. All cars must have working fire extinguishers mounted. Taping to bars illegal.

42. Cars must have an appropriately marked "on" & "off" switch to shut off power. Within reach of driver while strapped in.

43. Mandatory: All transmissions will have a flex plate safety shield. Automatic Transmissions will have a transmission blanket